Our company's main business: electromagnetic pulse valve, right-angle electromagnetic pulse valve, DMF-Z-76S electromagnetic pulse valve, DMF-Z-76S right-angle electromagnetic pulse valve, Langao DMF-Z-76S electromagnetic pulse valve, town Ping DMF-Z-76S electromagnetic pulse valve, welcome new and old customers to patronize ...15031895868 Order hotline: 15031895868
DMF-Z-76S Solenoid Pulse Valve
Solenoid Pulse Valve @Straight Angle Solenoid Pulse Valve @ DMF-Z-76S Solenoid Pulse Valve @ DMF-Z-76S
受脉冲阀喷吹控制仪输出信号的控制，脉冲阀一端接压缩空气包，另一端接喷吹管，脉冲阀背压室接控制阀，脉冲控制仪控制着控制阀及脉冲阀开启。 The DMF-Z-76S electromagnetic pulse valve is controlled by the output signal of the pulse valve injection controller. One end of the pulse valve is connected to the compressed air bag, and the other end is connected to the injection pipe. The pulse valve back pressure chamber is connected to the control valve. The pulse controller controls the control valve. And the pulse valve opens. When there is no signal output from the controller, the exhaust port of the control valve is closed and the pulse valve nozzle is closed. When the controller sends a signal, the exhaust port is controlled to open. A pressure difference occurs on both sides of the diaphragm, and the diaphragm is displaced due to the pressure difference. The pulse valve is blown open. At this time, the compressed air is ejected from the air bag through the pulse valve through the orifice of the blowing pipe (the gas emitted from the blowing pipe is a primary air). ). Pulse valve life: five years under the conditions of standardized installation, correct use and reasonable maintenance.
DMF-Z-76S electromagnetic pulse valve technical requirements:
1. The working pressure of the product is 0.1MPa ～ 0.7MPa, and the medium is air that has been degreased and dewatered.
2. When the working voltage of the solenoid valve is 85% of the rated voltage under the condition of the nominal air supply pressure of the product, the opening response time of the solenoid pulse valve should be less than 0.03s.
3. When the working gas source pressure is 0.1MPa, the pulse valve can be closed.
4. The product should be able to withstand a gas pressure of 0.8MPa.
5. Under the specified environmental conditions, the insulation resistance of the electromagnetic coil to the shell should be greater than 1MΩ.
6. Under the condition that the room temperature is 5 degrees to 35 degrees and the relative humidity does not exceed 85%, the electromagnetic coil can withstand the voltage of 50Hz and 250V to the shell, and there is no breakdown for 1min.
7. The electromagnetic pulse valve should be able to work normally after withstanding vibration at a frequency of 20Hz, a full amplitude of 2mm, and a duration of 30min.
8. Under normal use conditions, the cumulative service life of the diaphragm should be greater than 800,000 times.
9. There is no obvious coating peeling, scratches, burrs and other damage on the valve surface.
Working principle of DMF-Z-76S electromagnetic pulse valve:
The diaphragm divides the electromagnetic pulse valve into two front and rear air chambers. When the compressed air is turned on, the compressed air enters the rear air chamber through the orifice. At this time, the pressure of the rear air chamber will bring the diaphragm assembly close to the output port of the valve. The solenoid pulse valve is in the "closed" state. The electric signal of the pulse spray controller moves the armature of the electromagnetic pulse valve back, the vent hole of the air chamber behind the valve opens, the back chamber quickly loses pressure, the diaphragm assembly moves backward, and compressed air is blown through the valve output port. The electromagnetic pulse valve is at "On" state. The electrical signal of the pulse blowing controller disappears, the armature of the electromagnetic pulse valve is reset, the vent hole of the rear air chamber is closed, and the pressure of the rear air chamber is raised to make the diaphragm assembly close to the output port of the valve, and the electromagnetic pulse valve is in the "closed" state.
Botou Junzheng Environmental Protection Equipment Co., Ltd. has an experienced and strong production and sales team, focusing on the production and research and development of electromagnetic pulse valves. The design concept and manufacturing technology of the peers have achieved remarkable results in the environmental protection equipment industry, and actively develop new products for customers with low cost, high production efficiency and meeting customer needs. The company is determined to provide high-quality electromagnetic pulse valve products for the majority of demanding groups, always adhere to the principles of integrity and reciprocity, and insist on impressing customers with sincere service.
Working range of DMF-Z-76S electromagnetic pulse valve :
The main applications are chemical industry, building materials, metallurgy, machinery, food, petroleum, pharmaceuticals, waste incineration, thermal power generation, industrial kiln and other industries for dust-containing gas purification and dust material recovery. The selection of the pulse solenoid valve depends on the dust properties of the dust and is discharged from the flue. The frame of the filter bag should have sufficient strength, stiffness, perpendicularity, and correctness of dimensions to prevent compression deformation. It is necessary to consider whether the dust contains acid, alkali or strong corrosive substances. According to the nature of the dust, a suitable filter material is selected, so that the filter bag can normally absorb the dust without affecting its service life. Properly choose a dust bag suitable for the corresponding dust temperature. The filter bag will shorten the service life if it is light, and it will be burned in a short time if it is serious. Therefore, when the pulse solenoid valve is selected, the inlet temperature of the dust collector must be measured and calculated, and the corresponding dust bag should be selected. The smoke passing through the electric field passes through the electric field area and enters the bag area. The outer surface of the filter bag enters the inner cavity of the filter bag. Dust is trapped on the outer surface of the filter bag, and the pure gas is exhausted from the inner cavity to the flue. The essential. If the temperature is too high, the dust-removing cloth bag selected exceeds the normal use temperature, damaged during transportation, the filter bags contact each other after being installed in the dust collector, and the bagging problem.
Junzheng environmental protection equipment establishes the "five high" standards of high starting point, high goal, high quality, high efficiency and benefit, forging good quality products and gaining a broad sales market. The supplied electromagnetic pulse valve is mainly used for dust removal, and is favored by a large number of demand groups in the country. Companies with good reputation, strong strength, quality products, low prices to serve customers. Over the years of continuous development, the scale of Junzheng's environmental protection equipment has continued to grow. Our company provides the services of a complete sales and after-sales team, and has obtained extensive support from users in the demand group. The company pays attention to product quality and provides complete and meticulous services. For the electromagnetic pulse valves sold by the company, the company will not only deliver the products on time within the time negotiated by both parties, but also provide high-quality after-sales service.
The development of Botou Junzheng Environmental Protection Equipment Co., Ltd. cannot be separated from the care and support of all sectors of society. Looking back, looking forward to the future, Junzheng Environmental Protection Equipment will continue to strive to provide good electromagnetic pulse valves for demanding groups. The company implements a professional and intensive business strategy, gives full play to its advantages in all aspects, and focuses on the development of the machinery and hardware industry. With many years of experience and integrated solutions, it ultimately improves customer value and achieves a win-win situation. We are willing to cooperate with you for a better tomorrow. Welcome friends from all walks of life to guide! Address: Wangtun Village, Siying Township.
Botou Junzheng Environmental Protection Equipment Co., Ltd. is a professional manufacturer of environmental protection dust removal equipment integrating design, development, manufacturing, installation, commissioning and after-sales service. The company is located in Botou, Hebei Province, which is known as the “Hometown of Yali”. City, the company is close to the Beijing-Shanghai Railway, the Beijing-Shanghai Expressway and the 104 National Highway in the east, and the 106 National Highway in the west is connected to the Shihuang Expressway.
The main products of Junzheng Environmental Protection are: bag dust collector, pulse dust collector, cyclone dust collector, stand-alone dust collector, filter cartridge dust collector, boiler dust collector, electrostatic dust collector, desulfurization and denitrification dust collector, woodwork dust collector, wet dust collector, Exhaust gas treatment equipment, industrial dust collectors, etc. Dust collector bag, dust collector frame, electromagnetic pulse valve, dust humidifier, star discharger, bucket elevator, plug valve butterfly valve, pulse controller, screw conveyor, electric dust removal accessories, etc. It is used for the recovery of particulate dust and fine dust in the waste gas of large, medium and small enterprises, such as chemical industry, power industry, metallurgy, asphalt mixer and other waste gas.
Junzheng Environmental Protection has more than one hundred types of dust collector equipment and its various accessories. Dust removal equipment is strictly controlled from design, manufacturing and inspection. The manufacturing standards are strictly implemented in accordance with national operating process regulations. Yanzhi Factory takes quality as the credibility and technology investment as the breakthrough point to produce more high-grade, high-quality, high-performance and durable bag-type dust collectors, which better serve customers, so it is widely received by customers across the country. Praise.
Over the years, we have received the love and support of customers and friends from all walks of life. Through the unremitting efforts of all employees, we have broken a path of market-oriented and quality-oriented survival, continuous improvement, continuous development and innovation, and established a firm quality The belief in winning has created brilliant performance with rapid growth year after year. Adhering to the business philosophy of “high requirements, high starting point, high standards”, Junzheng Environmental Protection develops the market with the best quality, captures the market with the most reasonable price, and wins credibility with the most thoughtful service. We are the most professional in the production of dust collector accessories.
All the staff of Junzheng Environmental Protection Co., Ltd. warmly welcome friends from all walks of life to visit and guide us. We are willing to work with you to create the better future with the best service and the most sincere heart!
Botou Junzheng Environmental Protection Equipment Co., Ltd.
Contact: Manager Chang
Company QQ: 505310586
Email: [email protected]
Address: Siying Industrial Development Zone, Botou City, Hebei Province